Good Ford 2.3 TURBO head

usmcgunner · 10-08-2012, 10:59 AM

I need a good 2.3 Turbo Ford head, to put on my Merkur, when it gets down here this weekend. I have a fully built race head being finished up, in Delaware, but wont be ready.

I want something I cant put on, and start driving it again, its been a LONG 4 8 months since I last drove it.

The heads are compatable with the Thunderbird Turbo Coupe, or Mustang SVO.

stackz · 10-09-2012, 03:52 PM

if you want an actual good uncracked 2.3t head, good luck. stupid hard to find now days. might get lucky on turboford.org.

just grab a DP head from a mustang or ranger at the u-pull for cheap, leave one side of plugs just in and not connected and knock yourself out while waiting on the built head.

usmcgunner · 10-09-2012, 08:53 PM

I can find them everywhere on TF, and Merkursport, but nothing close enough to pick up. I shipped a Ranger Roller head to TX. Right before I got this head. I really should have kept it.

usmcgunner · 10-20-2012, 08:50 AM

Not needed anymore. I got my built head. I got it finished, and is now on the car. I need to get it torqued down, and timing set. Before I run it, though, I need to get a custom piece of intercooler piping made. My blow off valve hits the ground,

10-08-2012, 10:59 AM	#1
usmcgunner Senior Member Join Date: Aug 2012 Location: Beaufort, SC Posts: 788	Good Ford 2.3 TURBO head I need a good 2.3 Turbo Ford head, to put on my Merkur, when it gets down here this weekend. I have a fully built race head being finished up, in Delaware, but wont be ready. I want something I cant put on, and start driving it again, its been a LONG 4 8 months since I last drove it. The heads are compatable with the Thunderbird Turbo Coupe, or Mustang SVO. __________________ 1988 Merkur XR4Ti. Don't judge me on what I drive, but how I drive it.

10-09-2012, 08:53 PM	#3
usmcgunner Senior Member Join Date: Aug 2012 Location: Beaufort, SC Posts: 788	I can find them everywhere on TF, and Merkursport, but nothing close enough to pick up. I shipped a Ranger Roller head to TX. Right before I got this head. I really should have kept it. __________________ 1988 Merkur XR4Ti. Don't judge me on what I drive, but how I drive it.

10-20-2012, 08:50 AM	#4
usmcgunner Senior Member Join Date: Aug 2012 Location: Beaufort, SC Posts: 788	Not needed anymore. I got my built head. I got it finished, and is now on the car. I need to get it torqued down, and timing set. Before I run it, though, I need to get a custom piece of intercooler piping made. My blow off valve hits the ground, __________________ 1988 Merkur XR4Ti. Don't judge me on what I drive, but how I drive it.

Thread Tools
Show Printable Version Email this Page
Display Modes
Switch to Linear Mode Hybrid Mode Switch to Threaded Mode

10-09-2012, 03:52 PM	#2
stackz Senior Member Join Date: Sep 2009 Location: james island, sc Posts: 121	if you want an actual good uncracked 2.3t head, good luck. stupid hard to find now days. might get lucky on turboford.org. just grab a DP head from a mustang or ranger at the u-pull for cheap, leave one side of plugs just in and not connected and knock yourself out while waiting on the built head.