|
|
|
03-27-2014, 08:00 AM
|
#1 |
|
Senior Member
Join Date: Aug 2010
Posts: 2,809
|
New Pistol Build
Figured I'd share this......
All that's missing is the buffer tube assembly and my sights of choice PSA stripped lower PSA LPK PSA stripped upper PSA upper parts Voodoo Innovations 7.5" barrel Yankee Hill Machine low-pro gas block Stainless pistol gas tube (also have a pigtail if needed) AP customs carbon fiber handguard (had to cut about 1" off of it) Leavang linear compensator Nickel Boron BCG BCM gunfighter mod 3 charging handle Blackhawk grip (probably gonna swap this one out for something a little more supple) Phase 5 pistol buffer tube kit H2 and H3 buffers for tuning once I get to put some rounds through it. After cutting the handguard I need to refinish the end of the rail section, guess I'll just paint it. I was able to incorporate an endcap though, think it really cleans up the front of the barrel.  
|
|
|
|
03-27-2014, 12:30 PM
|
#2 |
|
Senior Member
Join Date: Jun 2008
Location: Goose Creek
Posts: 763
|
shweet! ive got so many builds in my head and not enough money in my bank...definately doing a pistol in the future
__________________
 
|
|
|
|
|
03-30-2014, 10:51 AM
|
#3 |
|
Senior Member
Join Date: Aug 2010
Posts: 2,809
|
Put a few magazines through her this morning. HOLY FUCKING LOUD!
Looks good and functions flawlessly though... 
|
|
|
|
|
03-30-2014, 07:03 PM
|
#4 |
|
creepy azz cracka
Join Date: Nov 2008
Location: Summerville
Posts: 1,587
|
With that short barrel, traditional .223 off the shelf ammo will only be able to put part of the powder charge towards pushing the bullet. The powder that hasn't yet burned by the time the bullet leaves the muzzle will just make the report very loud. I'll bet that pistol has one hell of a muzzle flash at night!
If you are into loading your own, try a faster burn rate powder such as IMR 4198 or its Hodgdon cousin H4198 to see if the muzzle blast calms down some for you.
__________________
"I came into this world kicking, screaming,and covered in someone else's blood, I have no problem leaving the same way!" ÔÇ£If you carry a gun, people will call you paranoid. ThatÔÇÖs ridiculous. If I have a gun, what in the hell do I have to be paranoid about?ÔÇØ -Clint Smith, Thunder Ranch. |
|
|
|
|
03-31-2014, 08:47 AM
|
#5 |
|
Senior Member
Join Date: Jun 2008
Location: Upstate, SC
Posts: 2,684
|
sonic weaponry
__________________
FIRSBIRZ 
|
|
|
|
|
03-31-2014, 09:25 AM
|
#6 |
|
Senior Member
Join Date: Aug 2010
Posts: 2,809
|
Muzzle flash is crazy, even in the daytime.
|
|
|
|
|
06-26-2014, 04:29 PM
|
#7 |
|
Senior Member
Join Date: Aug 2010
Posts: 2,809
|
Got the Sig brace installed, and switched lowers. Figured the Gadsden lower was fitting for obvious reasons. Also got the Primary Arms micro dot installed on a PA QD mount/riser. It is now complete....
|
|
|
|
|
06-27-2014, 12:19 AM
|
#8 |
|
Senior Member
Join Date: May 2008
Location: Myrtle Beach
Posts: 2,347
|
Looks good. Where'd you get the end cap? I need one for my rifle.
__________________
|
|
|
|
|
06-27-2014, 02:36 AM
|
#9 |
|
Senior Member
Join Date: Aug 2010
Posts: 2,809
|
It was part of the AP customs carbon tube. I cut some off of the end, so thought I wasn't going to be able to use it, but I figured out a way to screw it in. I have seen them sold though, not sure where.
Appears to lots available when googling "ar handguard endcap." |
|
|
|
 |
| Thread Tools | |
| Display Modes | |
|
|
Hybrid Mode
