TBSS Christmas list

[Carlrx7]

The warranty expires on the trailblazer in February so to ease the beating on the car I would like some input on how to make this big turd go fast!! Time to start making a list of things buy.

100% STOCK 2006 TBSS AWD

Would like to start with at least these 3 things
LS1 E-Fans
RPM Level VI transmission
3200 TC
about 3.5k

Now I have one requirement, its my official DD so it needs to have a mellow exhaust, so not touching the exhaust.

Trying to keep this next part to around 5-6k

Three ideas.

1) TVS 1900 Blower kit, good power down low coupled with the TC and the AWD should really get it off the line. should make about 450awhp

2) STS turbo kit, sweet turbo sound, nice exhaust note, and along with the TC should be pretty good off the line as well. 450-500awhp

3) Forge the bottom end of short block and a 175-200 progressive hit of nitrous. This would be my cheapest route, and probably the fastest. BUT I HATE refilling bottles, I also do not like waiting for it to explode.

Im leaning towards the TVS(50%), then the STS(30%), then the Nitrous(20%)

My goal? Mid 7's in the 1/8 and a smile from ear to ear.

-Carl

[BigdaddyDupree]

cam converter longtubes and tune neil went a 7.66. thats an easy goal.

[minytrker]

Originally Posted by BigdaddyDupree

cam converter longtubes and tune neil went a 7.66. thats an easy goal.

Thats a 2wd not a awd. The awd are always slower mod for mod. The only thing the awd works better for is street racing.

[Carlrx7]

Originally Posted by BigdaddyDupree

cam converter longtubes and tune neil went a 7.66. thats an easy goal.

No spray?

Also his exhaust is too loud to be my DD.

[BigdaddyDupree]

all motor i agree with lorenz but still you could be close with cam converter andd boltons. exhaust is a choice

[ElecTech]

I vote Maggie. Big fan of the Maggie and if you do it, step up to the 2300. I wouldn't bother with the 1900 unless the other just won't fit.

[bwelch]

Naawz

[1998ta__1991rs]

I would get gerald to build the tranny any day over an RPM, every RPM trans ive had expierence with was junk

my truck went 8.0 bone stock with a rich 150 pill in it

with a low lift stealth cam, vig 3800 converter, e fans, and a filter through stock manifolds went 7.85 on 29" drag radials on motor

no need for the forged bottom end with a 200 shot, LS2's can handle plenty more than that when tuned correctly

if you only want mid 7's it can be done on motor pretty cheap and easy

[chrisheltra]

Originally Posted by Carlrx7

No spray?

Also his exhaust is too loud to be my DD.

Who needs exhaust when you can haz turboz??

[Carlrx7]

Im waiting for someone to vote for all three. Lol

[PapaBear]

I vote for the STS, b/c I want you to pony up and do it before I do.......to reassure me!

[LXtasy]

vts was my vote. I have scanned that kit a couple of times for my truck. But right now with all the fires in the oven, I am in the same boat as you. but probably will go nitrous first

[Carlrx7]

Hmm, who local can take my shortblock to and have them throw in some forged rods and pistons and do all the blueprinting and balancing for me? any price? pretty much reuse the stock crank and block. might clean it up to 370ci. nothing fancy

[chrisheltra]

I know a guy who might do it but Ill let him chime in if hes interested instead of me volunteering him.

[1998ta__1991rs]

Originally Posted by Carlrx7

Hmm, who local can take my shortblock to and have them throw in some forged rods and pistons and do all the blueprinting and balancing for me? any price? pretty much reuse the stock crank and block. might clean it up to 370ci. nothing fancy

Mike's Machine Shop in Orangeburg, best around with ls motors

[PapaBear]

How much for somethin like that you think?

[gearmesh, inc.]

That factory 4L70E in the TBSS already has the 5 pinion planets, hardened input shaft, hardened output shaft, and hardened stator support. All it needs for aftermarket parts is a double cage forward sprag, beast sun shell, the input drum reinforcement sleeve, 7 plate Raybestos Blue Plate 3-4 clutch pack, and the Transgo HD2 shift kit. With a Carbonite 2-4 band, the factory Corvette servo equipped with some aftermarket d-ring rubber seals has enough force to hold 2nd gear without resorting to those $120 aftermarket servos.

The above mods to a 4L65/70 will readily survive 700 horsepower, assuming the factory line pressure cutback in 2nd gear on up is taken out of the tune.

If nothing is broke or worn out in your current 4L65/70 trans yet, total cost for the above improvements should be ~$1000-$1200 bench cost using your existing trans.

[blkscls1z]

Efans, Trans, Stall and a tune.

FWIW, I haven't had any issues with my RPM trans.

You could also look into a L92 H/C/I setup. There have been guys putting down good numbers (Dyno & Track) with that setup & the cam isn't big at all.

L92 setup pricing

http://www.pcmforless.com/index.php?...d=73&Itemid=85

L92 dyno

http://www.pcmforless.com/index.php?...g2_itemId=3282

Originally Posted by Carlrx7

Hmm, who local can take my shortblock to and have them throw in some forged rods and pistons and do all the blueprinting and balancing for me? any price? pretty much reuse the stock crank and block. might clean it up to 370ci. nothing fancy

If you do this then you might as well just get the TVS2300.

I'll make the decision easy for you. If you fly out to Qatar and pick me up, i'll buy you whatever TVS you want lol. I hope to be back this weekend sometime.

[Matts94Z28]

Originally Posted by 1998ta__1991rs

Mike's Machine Shop in Orangeburg, best around with ls motors

x1000

or Simmons

[Carlrx7]

Originally Posted by blkscls1z

I'll make the decision easy for you. If you fly out to Qatar and pick me up, i'll buy you whatever TVS you want lol. I hope to be back this weekend sometime.

how about i just buy you a commercial ticket to leave out of doha int.?